Home › Washington › Mason County

Mason County, WA Wells: 24% of 37 Wells High in Manganese

Data updated November 12, 2026. Covers private wells, not public water systems.

Low Risk
Few tested wells exceed a health limit Based on 26 wells tested Confidence: Moderate
Top concerns in this county Also test every year for bacteria and nitrate.
Testing strongly recommended Test your well →Mail-in kit sold on Amazon, results in about a weekFind a certified lab

What this means for you

Your health

Nitrate and arsenic look unlikely here, but they have no taste or smell, so they are still worth a test.

Everyday problems

Manganese: Manganese leaves black or brown stains and can make water taste bitter or metallic. At high levels it can also affect health, especially for babies, so use other water for baby formula if your well is high. Source

Iron: Iron leaves orange or brown stains on sinks, toilets and laundry, can make water taste metallic, and can clog pipes and fixtures. It is not a health risk.

Fixes: If a test finds manganese or iron over the taste or staining level, the usual fix is an iron and sulfur filter, like the Matrixx InFusion Iron & Sulfur Eradication System. A water softener, like the Matrixx Smart Metered Water Softener, also handles small amounts of manganese and iron. All products on this page.

Find out what's in your well

The only way to know is to test. For a well in Mason County, make sure the test covers:

  • Manganese
  • Iron
  • Bacteria and nitrate, every year

What tests found in Mason County

Over a health limitOver a taste or staining levelFound, under the limitUnder the limit or not foundComputer estimate
SubstanceTestedOver the limitResultsConfidenceRisk
Health concerns
Nitrate 26 wells 0% Moderate Low risk

Nitrate across Washington →

Water tests from agencies

0 of 26 wells tested since 2005 were above the EPA limit of 10 parts per million (as nitrogen).

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 2005–2016

USGS estimate

USGS predicts typical nitrate around 0.08 parts per million (as nitrogen) in private wells here (compare the EPA limit of 10 parts per million (as nitrogen)).

Source: USGS nitrate estimate for private wells (computer model), 1988–2018

If a test finds nitrate over the limit, the usual fix is a reverse osmosis system, like the American Made Reverse Osmosis System ($599–$799).

Arsenicacross the county USGS estimate about 2% chance Low Low risk

Arsenic across Washington →

Coliform Bacteria 3 wells 2 of 3 Low Too few tests

Water tests from agencies

2 of 3 wells tested since 2016 were positive for coliform bacteria.

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 2016

If a test finds coliform bacteria, find and fix how water gets in, then have the well disinfected (shock chlorination) and test again. If it comes back, the usual fix is a UV disinfection system, like the Pulsar Max Plus UV Disinfection System ($2,290–$2,540).

Lead 3 wells 0 of 3 Low Too few tests

Water tests from agencies

0 of 3 wells tested since 2016 were above the EPA action level of 15 parts per billion.

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 2016

If a test finds lead over the limit, the usual fix is a whole-house lead and PFAS filter, like the Pioneer Whole-House Lead, Cyst & PFOA/PFOS Removal System ($1,669–$2,364). Running the tap before drinking helps.

Uranium 3 wells 0 of 3 Low Too few tests
E. coli 3 wells 0 of 3 Low Too few tests
Everyday water problems
Manganese 37 wells 24% Moderate Common

Manganese across Washington →

Black or brown staining and a bitter, metallic taste.

Water tests from agencies

9 of 37 wells tested since 1971 were above the EPA taste-and-staining guideline of 0.05 parts per million.

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 1971–2016

USGS estimate

USGS estimates about a 4% chance that a private well here has manganese above the EPA health advisory level of 0.3 parts per million. At that level it can harm health, especially for babies.

Source: USGS manganese estimate for private wells (computer model), 1988–2018

If a test finds manganese over the taste or staining level, the usual fix is an iron and sulfur filter, like the Matrixx InFusion Iron & Sulfur Eradication System ($3,295–$3,395).

Iron 40 wells 12% Moderate Common
Sodium 26 wells 8% Moderate Sometimes found

A salty taste at higher levels.

Water tests from agencies

2 of 26 wells tested since 2005 were above the World Health Organization's taste level of 200 parts per million; 3 of 26 were above the EPA guidance level of 20 parts per million for people on a very low-sodium diet.

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 2005–2016

If a test finds high sodium, the usual fix is the same as for Nitrate (above).

Chloride 26 wells 8% Moderate Sometimes found

A salty taste, and it can speed up corrosion of pipes, fixtures and water heaters.

Water tests from agencies

2 of 26 wells tested since 2005 were above the EPA taste guideline of 250 parts per million.

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 2005–2016

If a test finds chloride over the taste or staining level, the usual fix is the same as for Nitrate (above).

Sulfate 26 wells 4% Moderate Sometimes found
pH 28 wells 4% Moderate Sometimes found

Acidic water can corrode pipes and fixtures, and can dissolve lead and copper from plumbing into your water.

Water tests from agencies

1 of 28 wells tested since 2005 were outside the recommended pH range (6.5 to 8.5).

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 2005–2016

If a test finds acidic water (low pH), the usual fix is a pH balancing filter, like the Matrixx pH Balancing Backwashing Filter System ($1,395–$1,595).

Hardness 62 wells 3% Moderate Sometimes found

Hard Water across Washington →

Scale on fixtures and in water heaters, and soap that lathers poorly.

Water tests from agencies

2 of 62 wells tested since 1971 were above the USGS level for hard water (120 parts per million).

Source: Well water tests from USGS, EPA and state agencies (Water Quality Portal), 1971–2016

If a test finds hard water, the usual fix is a water softener, like the Matrixx Smart Metered Water Softener ($1,467–$1,775).

Other substances tested
Fluoride 40 wells 0% Moderate Low risk

Fluoride across Washington →

Nitrite 26 wells 0% Moderate Low risk

Nitrate across Washington →

PFASacross the county USGS estimate about 14% chance Low Not rated

USGS estimate

USGS estimates about a 14% chance that a private well here has some PFAS ("forever chemicals") in it. This counts any amount found; most are far below EPA limits.

Source: USGS PFAS estimate for private wells (computer model), 2019–2022

No households on private wells here live within 1 mile of a known PFAS source (a site where PFAS was found, a reported PFAS release or firefighting-foam spill, or a PFAS maker, from EPA data). Source: EPA PFAS Analytic Tools.

If a test finds PFAS over the limit, the usual fix is the same as for Lead (above).

How we rate: High risk means 1 in 10 or more tested wells were over a health limit, or a USGS estimate of 20% or more. Moderate means 2 in 100 or more; Low, fewer. Confidence is High with 100 or more wells tested, Moderate with 20 to 99, and Low with fewer or a computer estimate only. With too few tests to judge, the county reads Risk Unknown. Stains, scale and taste are rated on their own and don't change the county's risk.

Check your ZIP code

Well water can differ from one part of a county to the next. Enter your ZIP code to see what the U.S. Geological Survey estimates for arsenic and nitrate in wells around you.

About wells here

  • About 15,800 households on private wells (USGS 2020). Source: USGS count of households on private wells, 2020.
  • 35% of people here rely on private wells (USGS 2015). Source: USGS water use estimates, 2015.
  • About 14% of households on private wells here (about 2,300 homes) live within 1 mile of groundwater pollution on the state's list or a Superfund site (the EPA's list of the most serious toxic waste sites). That does not mean their wells are affected, but it is a good reason to test. Source: Washington Ecology contaminated sites list.
  • USGS maps no limestone and similar rock with cracks and caves (karst) in this county. Source: USGS map of limestone and similar rock.
  • Radon in indoor air (EPA map): Zone 3 – low potential. Source: EPA Map of Radon Zones.
  • Since 2000, FEMA has declared 7 flood or hurricane disasters that included this county, most recently in 2026. Source: FEMA disaster declarations.Why it matters: Floodwater can carry bacteria and chemicals into a well. Test your water after any flood.
  • Since 2000, at least half of this county was in drought about 12% of the time, most recently with severe drought in 2022. Drought lowers the water table, and shallow wells can run low or dry. Source: U.S. Drought Monitor.

These are facts about the whole county. None of them means a particular well has a problem; only a test can tell you that.

Well water testing in Mason County

The only way to know what is in your well is to test it. The certified labs nearest Mason County are listed below. The closest is Thurston County Health Department Laboratory in Olympia, about 20 miles away. A mail-in kit is another option. Test every year for bacteria and nitrate, and here, also ask for manganese and iron.

Order a test kit Tap Score Advanced Well Water Test

A mail-in test from certified labs for more than 100 substances, with results in about a week.

Sold on Amazon · mailed to your home

Order a Tap Score Test →
Nearest certified lab Thurston County Health Department Laboratory

2000 Lakeridge Drive SW, Olympia

About 20 miles away · 360-867-2631

Call a lab first to ask which tests it runs and how to get a sample bottle.

More certified labs near Mason County

Certified lab Olympic Analytical LLC dba Vanguard Laboratory

2635 Parkmont Labe SW, Olympia

About 25 miles away · 360-967-7010

Every certified lab in Washington

These labs serve well owners across Mason County, including Allyn, Belfair, Grapeview, Hoodsport, Shelton, Skokomish and Union.

These labs are certified by Washington to test drinking water for bacteria, and most also test for nitrate. For other tests, ask the lab what it is certified for. See the state's list.

Rules about testing

  • Licensed child care programs in Washington that use a private well must test it every year for E. coli and nitrate. Source
Federal rules and home loans (6)
  • No federal law makes you test your own well. EPA and CDC recommend testing every year for bacteria, nitrate, pH and dissolved solids. Source
  • Fannie Mae and Freddie Mac loans don't require a well test. Your lender or local law may still require one. Source
  • If you buy with an FHA loan, the lender must confirm the well water is safe. A test is required for new homes and when there is a known problem. The results must be less than 180 days old. Source
  • With an FHA loan, a well that is closer to a septic system than HUD allows can still qualify if it meets local rules and a water test shows the water is safe. Source
  • If you buy with a USDA guaranteed loan and the home has a well, a health department or state-certified lab must test the water. The report must be less than 180 days old at closing. Refinances don't need a test. Source
  • If you buy with a VA loan and the home has a well, a neutral third party must test the water. You can't take the sample yourself. Results are good for 90 days. Source

Local health codes in this state have not been reviewed yet.

Local help

For up-to-date local news about wells and water testing, check the Mason County Public Health website.

Local health departments

From the Washington State Department of Health, Washington State Local Health Jurisdictions.

Products on this page

Test first, then fix only what your test finds. Certified labs near Mason County are listed above.

Tests

Test kit Tap Score Advanced Well Water Test

A mail-in test from certified labs for more than 100 substances, with results in about a week.

Sold on Amazon · mailed to your home

Order a Tap Score Test →

Fixes, if a test finds a problem

Usual fix American Made Reverse Osmosis System

For Nitrate, Arsenic, Uranium, Sodium, Chloride, Sulfate, Fluoride, Nitrite.

$599–$799

View product →
Usual fix Pulsar Max Plus UV Disinfection System

For Coliform Bacteria, E. coli.

$2,290–$2,540

View product →
Usual fix Pioneer Whole-House Lead, Cyst & PFOA/PFOS Removal System

For Lead, PFAS.

$1,669–$2,364

View product →
Usual fix Matrixx InFusion Iron & Sulfur Eradication System

For Manganese, Iron.

$3,295–$3,395

View product →
Usual fix Matrixx Smart Metered Water Softener

For Hardness. Also an option for Manganese, Iron.

$1,467–$1,775

View product →
Usual fix Matrixx pH Balancing Backwashing Filter System

For pH.

$1,395–$1,595

View product →
Another option APEC ROES-50 Essence 5-Stage Reverse Osmosis System

An option for Nitrate, Arsenic, Lead, Uranium, Sodium, Chloride, Sulfate, Fluoride, Nitrite, PFAS.

See price on Amazon

View on Amazon →
Another option HQUA-OWS-12 Whole House UV Water Purifier, 12 GPM

An option for Coliform Bacteria, E. coli.

See price on Amazon

View on Amazon →
Another option iSpring WGB32BM Whole House Iron & Manganese Filter

An option for Manganese, Iron.

See price on Amazon

View on Amazon →
Another option Matrixx Ultimate Iron, Sulfur & Softening System

An option for Manganese, Iron, Hardness.

$4,905–$5,322

View product →
Another option US Water Upflow Calcite pH Neutralizer Filter

An option for pH.

$995–$1,195

View product →
Another option Eddy Electronic Water Descaler (salt-free)

An option for Hardness.

See price on Amazon

View on Amazon →

Need help deciding?

Type in the numbers from your lab report and our free planner tells you what to fix first, which problems one system can handle together, and what you don't need to buy. Your numbers stay in your browser.

Make a treatment plan

Some of these are affiliate links. If you buy through them, we may earn a commission at no cost to you. As an Amazon Associate, we earn from qualifying purchases. Our picks do not affect what the data says.

Ready to test your well?

A mail-in kit or a certified lab near Mason County can test your water.

Mason County: Low RiskTest your well

For health departments, realtors and groups

Free ways to share what wells in Mason County show:

  • Add this to your website: a free card about wells in Mason County that updates itself.
  • Download the data behind this page for Washington. It is free to reuse if you credit YourWaterReport.
  • To cite this page: YourWaterReport, "Mason County, WA Wells: 24% of 37 Wells High in Manganese," https://yourwaterreport.com/states/wa/mason-county/, data updated November 12, 2026.

Sources and dates

All 15 data sources and when we retrieved them

Required credits

  • This product uses the Federal Emergency Management Agency's OpenFEMA API, but is not endorsed by FEMA. The Federal Government or FEMA cannot vouch for the data or analyses derived from these data after the data have been retrieved from the Agency's website(s). Data: OpenFEMA DisasterDeclarationsSummaries v2 (https://www.fema.gov/api/open/v2/DisasterDeclarationsSummaries).
  • The U.S. Drought Monitor is jointly produced by the National Drought Mitigation Center at the University of Nebraska-Lincoln, the United States Department of Agriculture, and the National Oceanic and Atmospheric Administration. Data courtesy of NDMC.
  • Contaminated Sites List, Cleanup and Tank Search, Washington State Department of Ecology.

How we get our numbers · Download the data